ada code for bridge sectioning

208.3 Location. Amusement Ride. Residential dwelling units required to comply with 233.3.1.1 shall be on an accessible route as required by 206. 703.4.1 Height Above Finish Floor or Ground. (2) Facilities with more than 50 beds covered by this part that provide common use bathing facilities shall provide at least one roll-in shower with a seat that complies with the relevant provisions of section 608 of the 2010 Standards. 216.2 Designations. Additional options such as armrests, head rests, seat belts, and leg support will enhance accessibility and better accommodate people with a wide range of disabilities. EXCEPTION: If at least 50 percent of the elevated play components are connected by a ramp and at least 3 of the elevated play components connected by the ramp are different types of play components, the play area shall not be required to comply with 240.2.1.2. Where a series of transfers are required to reach the amusement ride seat, each vertical transfer should not exceed 8 inches (205 mm). Characters shall be uppercase or lowercase or a combination of both. Where the reach depth exceeds 10 inches (255 mm), the high side reach shall be 46 inches (1170 mm) maximum for a reach depth of 24 inches (610 mm) maximum. Elevator landings shall comply with 407.2. 405.9 Edge Protection. (2) The path of travel requirements of 35.151(b)(4) shall apply only to alterations undertaken solely for purposes other than to meet the program accessibility requirements of 35.150. If a backing, cushion or pad is used, it must be firm. (c) Exception for structural impracticability. Additional factors affecting the ease with which the text can be distinguished from its background include shadows cast by lighting sources, surface glare, and the uniformity of the text and its background colors and textures. Clear pier space shall be permitted to be 36 inches (915 mm) wide minimum for a length of 24 inches (610 mm) maximum, provided that multiple 36 inch (915 mm) wide segments are separated by segments that are 60 inches (1525 mm) wide minimum and 60 inches (1525 mm) long minimum. Identification and directional signs for public TTYs shall be provided in accordance with 216.9. For example, office buildings may contain a room with exercise equipment to which these sections would apply. CDT Codes for Dental Bridge D6245 Pontic, porcelain/ceramic (bridge units) D6740 Retainer Crown - Porcelain/Ceramic With this dental procedure code, the prosthetic crown fitted over the tooth is made of porcelain or ceramic. Where existing toilet rooms or bathing rooms do not comply with 603, directional signs indicating the location of the nearest toilet room or bathing room complying with 603 within the facility shall be provided. Platform lifts shall be permitted to provide accessible routes to play components or soft contained play structures. Shelves shall be located 40 inches (1015 mm) minimum and 48 inches (1220 mm) maximum above the finish floor. In transfer type compartments, grab bars shall be provided across the control wall and back wall to a point 18 inches (455 mm) from the control wall. Advisory 240.2.1 Ground Level Play Components. 409.4.2 Floor Surfaces. 811.2 Clear Floor or Ground Space. The clear floor space shall be positioned for parallel approach to the side of the bed. 410.2 Floor Surfaces. Visiting areas shall comply with 232.5. Platform lifts shall comply with ASME A18.1 (1999 edition or 2003 edition) (incorporated by reference, see Referenced Standards in Chapter 1). Use Zone. Animal containment areas that are not for public use shall not be required to comply with these requirements or to be on an accessible route. 231.3.2 Court-Floor Holding Cells. (1) New construction and alterations subject to 36.401 or 36.402 shall comply with the 1991 Standards if the date when the last application for a building permit or permit extension is certified to be complete by a State, county, or local government (or, in those jurisdictions where the government does not certify completion of applications, if the date when the last application for a building permit or permit extension is received by the State, county, or local government) is before September 15, 2010, or if no permit is required, if the start of physical construction or alterations occurs before September 15, 2010. Where a kitchen is provided, it shall comply with 804. EXCEPTION: In elevator cars with more than one opening, hoistway doors and gates shall be permitted to be of the manual-open, self-close type. Accessible cells or rooms should be dispersed among different levels of security, housing categories, and holding classifications (e.g., male/female and adult/juvenile) to facilitate access. This code reports the . 903.7 Wet Locations. 209.2.2 Bus Loading Zones. An obstruction shall be permitted between the clear floor or ground space and the element where the depth of the obstruction is 10 inches (255 mm) maximum. Isolated or temporary interruptions in service due to maintenance or repairs may be unavoidable; however, failure to take prompt action to effect repairs could constitute a violation of Federal laws and these requirements. The ground level area beneath and immediately adjacent to a play structure or play equipment that is designated by ASTM F 1487 (incorporated by reference, see Referenced Standards in Chapter 1) for unrestricted circulation around the play equipment and where it is predicted that a user would land when falling from or exiting the play equipment. Wheelchair Space. 604.8.2.2 Doors. In detention and correctional facilities, signs not located in public use areas shall not be required to comply with 216. Two parking spaces shall be permitted to share a common access aisle. EXCEPTION: Where sloped entries are provided, the surfaces shall not be required to be slip resistant. EEOC can provide guidance regarding employers obligations to provide reasonable accommodations for employees with disabilities. 801.1 Scope. Notification devices shall not be connected to visible alarm signal appliances. Where existing elevators do not comply with 407, elevators complying with 407 shall be clearly identified with the International Symbol of Accessibility complying with 703.7.2.1. Work area equipment does not include passenger elevators and other accessible means of vertical transportation. However, the bridge retainer codes vary depending on whether or not an abutment was used to attach the bridge retainer to the implant body. Existing elevators shall not be required to comply with 407.2.1.5. Elevator cars shall comply with 407.4. EXCEPTION: Where multi-story residential dwelling units are one of the types of residential dwelling units provided, one-story residential dwelling units shall be permitted as a substitute for multi-story residential dwelling units where equivalent spaces and amenities are provided in the one-story residential dwelling unit. Edge protection is required only where railings, guards, or handrails are provided on a fishing pier or platform. If the start date for construction is on or after March 15, 2012, all newly constructed or altered State and local government facilities must comply with the 2010 Standards. If vanity counter top space is provided in non-accessible guest toilet or bathing rooms, comparable vanity counter top space, in terms of size and proximity to the lavatory, shall also be provided in accessible guest toilet or bathing rooms. The method and color of marking are not specified by these requirements but may be addressed by State or local laws or regulations. Ramp runs shall have a running slope not steeper than 1:12. The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface. Each assembly area required by 219 to provide assistive listening systems shall provide signs informing patrons of the availability of the assistive listening system. EXCEPTION: Tactile symbols required by 707.6.3.2 shall not be required to comply with 707.6.3.1. Raised courtroom stations, including judges benches, clerks stations, bailiffs stations, deputy clerks stations, and court reporters stations shall not be required to provide vertical access provided that the required clear floor space, maneuvering space, and, if appropriate, electrical service are installed at the time of initial construction to allow future installation of a means of vertical access complying with 405, 407, 408, or 410 without requiring substantial reconstruction of the space. 5 ( 126) Dental ADA Codes In this article show Translation of Current Dental Terminology American Dental Association (updated Oct 2022) Download ADA CODE.PDF How useful was this post? Queues and waiting lines servicing counters or check-out aisles required to comply with 904.3 or 904.4 shall comply with 403. The firmer the carpeting and backing, the lower the roll resistance. Where four or more entry points are provided for soft contained play structures, at least two entry points shall be on an accessible route. I Am Looking For Cdt Code For Extraction Under Bridge, Which . Amusement rides that are controlled or operated by the rider shall not be required to comply with 234.3. Accessible routes serving water play components shall be permitted to use the exceptions in 1008.2.3. In alterations, a projection of 5/8 inch (16 mm) maximum into the required clear width shall be permitted for the latch side stop. Stairs shall comply with 504. Transient Lodging. 707.6 Input. A single full-length mirror can accommodate a greater number of people, including children. icd-9-cm code 486 What is the cpt code for ileo cecectomy? Operable parts that are intended for use only by service or maintenance personnel shall not be required to comply with 309. The dot shall be 0.118 inch (3 mm) to 0.120 inch (3.05 mm) base diameter and in other aspects comply with Table 703.3.1. 608.2.2.1 Clearance. Accessible ATMs, including those with speech and those that are within reach of people who use wheelchairs, must provide all the functions provided to customers at that location at all times. 809.5.5 Residential Dwelling Unit Primary Entrance. 806.3 Guest Rooms with Communication Features. For example, a play area is built in two phases. Transfer supports are required on transfer platforms and transfer steps to assist children when transferring. 1007.1 General. 1008.3.2.2 Height. TTY. Where clocks are installed overhead, numerals and digits shall comply with 703.5. The NFPA 72 incorporates Underwriters Laboratory (UL) 1971 by reference. Operable parts of such hardware shall be 34 inches (865 mm) minimum and 48 inches (1220 mm) maximum above the finish floor or ground. Where a seat is provided in a standard roll-in shower compartment, it shall be a folding type, shall be installed on the side wall adjacent to the controls, and shall extend from the back wall to a point within 3 inches (75 mm) of the compartment entry. Most dental plans do not routinely cover implant supported crown and bridge services, or removable prosthodontics. In the first phase, there are 10 elevated play components and 10 elevated play components are added in the second phase for a total of 20 elevated play components in the play area. Seats shall comply with 610.3.1 or 610.3.2. 804.3.3 Exposed Surfaces. Visible and audible signals shall not be required at each destination-oriented elevator where a visible and audible signal complying with 407.2.2 is provided indicating the elevator car designation information. Unlike audible alarms, visible alarms must be located within the space they serve so that the signal is visible. A level landing is needed at the accessible door to permit maneuvering and simultaneously door operation. 208.2.4 Van Parking Spaces. Bus stop boarding and alighting areas shall have a firm, stable surface. Where a forward approach is provided, the clear floor or ground space shall provide knee and toe clearance complying with 306. Departures from particular requirements of either standard by the use of other methods shall be permitted when it is clearly evident that equivalent access to the facility or part of the facility is thereby provided. 505.10.1 Top and Bottom Extension at Ramps. The clear floor space adjacent to the control shall be located beyond the arc of the door swing. 405.7 Landings. 1008.4.5 Transfer Supports. 1007.3 Miniature Golf Holes. 206.7.10 Recreational Boating Facilities and Fishing Piers and Platforms. A play component that is approached above or below grade and that is part of a composite play structure consisting of two or more play components attached or functionally linked to create an integrated unit providing more than one play activity. 409.4.1 Inside Dimensions of Elevator Cars. EXCEPTION. Where transfer systems provide access to elevated play components, the reach ranges are not appropriate. If an audio headphone jack is provided on a speaker phone, a cutoff switch can be included in the jack so that insertion of the jack cuts off the speaker. 707.8 Braille Instructions. Sinks shall comply with 606. Amusement rides designed primarily for children, amusement rides that are controlled or operated by the rider, and amusement rides without seats, are not required to provide wheelchair spaces, transfer seats, or transfer systems, and need not meet the sign requirements in 216.12. The Department of Justice published revised regulations for Titles II and III of the Americans with Disabilities Act of 1990 ADA in the Federal Register on September 15, 2010. 224.1.2 Guest Room Doors and Doorways. Where sliding doors are in the fully open position, operating hardware shall be exposed and usable from both sides. Where a seat is not provided in standard roll-in type shower compartments, grab bars shall be provided on three walls. Shower compartments shall comply with 608. 105.2.5 NFPA. 503.3.3 Marking. 810.2.3 Connection. Advisory 706.3 Receiver Hearing-Aid Compatibility. 304.3.2 T-Shaped Space. Wheelchair accessible toilet compartments shall meet the requirements of 604.8.1 and 604.8.3. The high forward reach shall be 48 inches (1220 mm) maximum where the reach depth is 20 inches (510 mm) maximum. All other accessible slips are allowed to have the required pier clearance at the head of the slip. (1) An alteration that affects or could affect the usability of or access to an area of a facility that contains a primary function shall be made so as to ensure that, to the maximum extent feasible, the path of travel to the altered area and the restrooms, telephones, and drinking fountains serving the altered area, are readily accessible to and usable by individuals with disabilities, including individuals who use wheelchairs, unless the cost and scope of such alterations is disproportionate to the cost of the overall alteration. Car door closing shall not be initiated until the hoistway door is closed. (1) New construction of jails, prisons, and other detention and correctional facilities shall comply with the 2010 Standards except that public entities shall provide accessible mobility features complying with section 807.2 of the 2010 Standards for a minimum of 3%, but no fewer than one, of the total number of cells in a facility. Existing doors and gates without smooth surfaces within 10 inches (255 mm) of the finish floor or ground shall not be required to provide smooth surfaces complying with 404.2.10 provided that if added kick plates are installed, cavities created by such kick plates are capped. 242.4 Spas. Telephone keypads and computer keyboards differ in one significant feature, ascending versus descending numerical order. Medical care facilities that are subject to this part shall comply with the provisions of the 2010 Standards applicable to medical care facilities, including, but not limited to, sections 223 and 805. Partitions and doors should be designed to ensure people using accessible dressing and fitting rooms privacy equivalent to that afforded other users of the facility. 216.5 Parking. EXCEPTION: TTYs shall not be required at banks of telephones located within 200 feet (61 m) of, and on the same floor as, a bank containing a public TTY. 306.2.3 Minimum Required Depth. In residential dwelling units, the height of water closets shall be permitted to be 15 inches (380 mm) minimum and 19 inches (485 mm) maximum above the finish floor measured to the top of the seat. Access aisles shall not overlap the vehicular way. Is The An Ada Code For Sectioning A Bridge? 409.3 Elevator Doors. EXCEPTION: Handrails shall be permitted to protrude 4 1/2 inches (115 mm) maximum. 505.7.1 Circular Cross Section. 1008.2.2 Soft Contained Play Structures. Charles Blair - Code D9120. Advisory 607.6 Shower Spray Unit and Water. Benches shall comply with 903. Edge protection shall not be required on the sides of ramp landings having a vertical drop-off of 1/2 inch (13 mm) maximum within 10 inches (255 mm) horizontally of the minimum landing area specified in 405.7. 217.3 Volume Controls. See additional requirements at 28 CFR 35.151(e) and 28 CFR 35.151(f) and 28 CFR 36.406(d) and 28 CFR 36.406(e). Signs are more legible for persons with low vision when characters contrast as much as possible with their background. 1008.2.5.3 Handrails. Doors shall not swing into the clear floor space or clearance required for any fixture. Where a building is vacated for the purposes of alteration, and the altered building contains more than 15 residential dwelling units, at least 5 percent of the residential dwelling units shall comply with 809.2 through 809.4 and shall be on an accessible route as required by 206. Residential dwelling units required to provide communication features shall comply with 809.5. Where there are no railings, guards, or handrails, at least one clear floor or ground space complying with 305 shall be provided on the fishing pier or platform. The side of the transfer platform serving the transfer space shall be unobstructed. Parking space identification signs shall include the International Symbol of Accessibility complying with 703.7.2.1. Cross Slope. 704.2.2 Operable Parts. This exception for protruding objects applies to the ride devices, not to circulation areas or accessible routes in the queue lines or the load and unload areas. The top of the bench seat surface shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum above the finish floor or ground. 609.2.2 Non-Circular Cross Section. The use of a handset by the communications system is prohibited. 608.3.3 Alternate Roll-In Type Shower Compartments. See additional requirements at 28 CFR 35.151(h) and 28 CFR 36.406(g). EXCEPTION: In existing facilities, visible alarms shall not be required except where an existing fire alarm system is upgraded or replaced, or a new fire alarm system is installed. Copies of the referenced standards may be obtained from the National Fire Protection Association, 1 Batterymarch Park, Quincy, Massachusetts 02169-7471, (http://www.nfpa.org). The technical criteria for accessible means of egress allow the use of exit stairways and evacuation elevators when provided in conjunction with horizontal exits or areas of refuge. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Each addition that affects or could affect the usability of or access to an area containing a primary function shall comply with 202.4. Terms defined in Section 106.5 are italicized in the text of this document. Elevator hoistway and car doors shall open and close automatically. 223.1 General. 407.2.2.3 Audible Signals. 206.2.17 Play Areas. 224.1 General. In this example, an accessible route is not required to the second floor provided that all accessible units and all common use areas serving them are on the first floor. Amusement rides shall provide at least one wheelchair space complying with 1002.4, or at least one amusement ride seat designed for transfer complying with 1002.5, or at least one transfer device complying with 1002.6. In addition, lawn seating shall comply with 221.5. 409.4.6.1 Size. (A) Mechanical rooms, boiler rooms, supply storage rooms, employee lounges or locker rooms, janitorial closets, entrances, and corridors are not areas containing a primary function. Amusement rides designed primarily for children, where children are assisted on and off the ride by an adult, shall not be required to comply with 234.3. The space shall be 36 inches (915 mm) wide minimum and shall extend forward 48 inches (1220 mm) minimum from a line located 12 inches (305 mm) behind the rear edge of the seat. 206.2.8 Employee Work Areas. Individual self-service storage spaces shall be dispersed throughout the various classes of spaces provided. Where transfer systems are provided to connect to elevated play components, transfer systems shall comply with 1008.3. There are a variety of transfer devices available that could be adapted to provide access onto an amusement ride. Alterations include, but are not limited to, remodeling, renovation, rehabilitation, reconstruction, historic restoration, resurfacing of circulation paths or vehicular ways, changes or rearrangement of the structural parts or elements, and changes or rearrangement in the plan configuration of walls and full-height partitions. 703.6 Pictograms. In cells having more than 25 beds, at least 5 percent of the beds shall have clear floor space complying with 807.2.3. With the exception of transit facilities, which are covered by regulations issued by the Department of Transportation, there is no process for certifying that an alternative design provides equivalent facilitation. Access aisles shall extend the full length of the parking spaces they serve. In row seating, two wheelchair spaces shall be permitted to be located side-by-side. Grab bars shall not rotate within their fittings. In bus loading zones restricted to use by designated or specified public transportation vehicles, each bus bay, bus stop, or other area designated for lift or ramp deployment shall comply with 810.2. Reinforcement must be sufficient to permit the installation of rear and side wall grab bars that fully meet all accessibility requirements including, but not limited to, required length, installation height, and structural strength. Where membrane keys are the only method of input, each shall be tactilely discernable from surrounding surfaces and adjacent keys. Where clocks are provided for use by the public, the clock face shall be uncluttered so that its elements are clearly visible. Where the conditions in exception 3 are satisfied, existing facilities are only required to have one accessible boat slip with a pier clearance which runs the length of the slip. A grab bar 24 inches (610 mm) long minimum shall be installed on the control end wall at the front edge of the bathtub. In providing lines of sight, wheelchair spaces shall be dispersed. Objects are permitted to protrude a distance of 6 inches (150 mm) maximum along the front of the wheelchair space, where located 9 inches (230 mm) minimum and 27 inches (685 mm) maximum above the floor or ground surface of the wheelchair space. Characters shall contrast with their background with either light characters on a dark background or dark characters on a light background. The floor or ground surface of wheelchair spaces shall have a slope not steeper than 1:48 when in the load and unload position. 232.2.1 Cells with Mobility Features. 903.6 Structural Strength. 608.5.3 Alternate Roll-In Type Shower Compartments. Changes in level are not permitted. Many drivers, especially those who operate vans, find it more difficult to back into parking spaces than to back out into comparatively unrestricted vehicular lanes. 1006.2 Accessible Routes. 216.9 TTYs. 221.2.1.2 Luxury Boxes, Club Boxes, and Suites in Arenas, Stadiums, and Grandstands. Recreational boating facilities shall comply with 1003. Detention facilities include, but are not limited to, jails, detention centers, and holding cells in police stations. Revolving doors, revolving gates, and turnstiles shall not be part of an accessible route. Areas of sport activity shall not be required to comply with 302. EXCEPTION: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable. Where provided, check writing surfaces shall comply with 902.3. 234.1 General. 206.7.6 Guest Rooms and Residential Dwelling Units. Communication features shall be provided at the residential dwelling unit primary entrance complying with 809.5.5. Changes in level are not permitted. Although covered entities are permitted to limit the scope of an alteration to individual elements, the alteration of multiple elements within a room or space may provide a cost-effective opportunity to make the entire room or space accessible. 209.4 Valet Parking. The display screen shall comply with 707.7. If farecards have one tactually distinctive corner they can be inserted with greater accuracy. The following example applies to a boat launch ramp boarding pier: A chain of floats is provided on a launch ramp to be used as a boarding pier which is required to be accessible by 1003.3.2. 809.5.2 Residential Dwelling Unit Smoke Detection System. Handrails shall not rotate within their fittings. Wheelchair spaces shall be located in not less than 20 percent of all boxes provided. Where the minimum number of boat slips required to comply with 1003.3.1 has been met, no further dispersion shall be required. Audible signals shall have a frequency of 1500 Hz maximum. Elevator operation shall be automatic. 223.2 Hospitals, Rehabilitation Facilities, Psychiatric Facilities and Detoxification Facilities. A single wheelchair space shall be 36 inches (915 mm) wide minimum Where two adjacent wheelchair spaces are provided, each wheelchair space shall be 33 inches (840 mm) wide minimum. Braille shall comply with 703.3. Sloped entries shall comply with Chapter 4 except as modified in 1109.3.1 through 1109.3.3. Changes in level are not permitted. EXCEPTION: Where sign space is limited, characters shall not be required to exceed 3 inches (75 mm). 408.3.2 Swinging Doors. Elevator doors shall be the horizontal sliding type. Some amusement rides and attractions that have unique designs and features are not addressed by these requirements. 206.2.15 Golf Facilities. Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply. Self-service storage facilities shall provide individual self-service storage spaces complying with these requirements in accordance with Table 225.3. 1005.2.1 Height. Mezzanines have sufficient elevation that space for human occupancy can be provided on the floor below. The anatomy of a Maryland bridge consists of pontic/s and wings. In existing piers, clear pier space shall be permitted to be located perpendicular to the boat slip and shall extend the width of the boat slip, where the facility has at least one boat slip complying with 1003.3, and further compliance with 1003.3 would result in a reduction in the number of boat slips available or result in a reduction of the widths of existing slips. 902.4 Dining Surfaces and Work Surfaces for Childrens Use. 810.3 Bus Shelters. Floor designations shall be provided in both tactile characters and braille. Factors to be considered in comparing one dwelling unit to another should include the number of bedrooms; amenities provided within the dwelling unit; types of common spaces provided within the facility; and location with respect to community resources and services, such as public transportation and civic, recreational, and mercantile facilities. Where four or more public pay telephones are provided in a private building, at least one public TTY shall be provided in the building. When distinguishing between the different types of ground level play components, consider the general experience provided by the play component. The standard includes additional provisions for runway enclosures, electrical equipment and wiring, structural support, headroom clearance (which is 80 inches minimum), lower level access ramps and pits. 407.2.2.4 Differentiation. Every effort should be made to ensure that such alarms can be differentiated in their signal from fire alarms systems and that people who need to be notified of emergencies are adequately safeguarded. Door and gate closing speed shall comply with 404.2.8. Where the interior width of the amusement ride is greater than 53 inches (1345 mm), seating is provided for more than one rider, and the wheelchair is not required to be centered within the amusement ride, a companion seat shall be provided for each wheelchair space. Circulation Path. The accessible route shall connect ground level play components required to comply with 240.2.1 and elevated play components required to comply with 240.2.2, including entry and exit points of the play components. Any facility, or portion of a facility, located within an amusement park or theme park which provides amusement without the use of an amusement device. A folding or non-folding seat shall be provided in transfer type shower compartments. The radius of curvature at the leading edge of the tread shall be 1/2 inch (13 mm) maximum. 704.3 Volume Control Telephones. The lack of a design requirement does not mean that covered entities are not required to provide services to people with disabilities where accessible rooms are not dispersed in specialty areas. Where transfer systems are provided, consideration should be given to the distance between the transfer system and the elevated play components.